Get an AlldataDIY Repair Info Subscription Special Thanks To: AC Kits.com

Author Topic: 2001 GMC Sierra P0300 Multiple Misfire  (Read 6125 times)

Offline Big Kahuna

  • Newbie
  • *
  • Posts: 7
2001 GMC Sierra P0300 Multiple Misfire
« on: June 11, 2008, 09:24:57 PM »
 ???
Ok getting the P0300 multilpe misfire code on my 2001 GMC Sierra with the 5. 3L engine.   Got new plugs and wires.   Checked spark with spark tester all coils are firing.   Check resistance on injectors they checked out good.   Tested fuel pressure key on 52, engine running (idle) 48, leak test for 5 mintues no drop in pressure.
Vehicle is running rough, hard to accelerate,  stumble during acceleration.   Dual exhaust on this truck driver side exhaust is just barely blowing out passenger side blowing out good.   Was getting code before I notice exhaust pressure.   Could it be Cat Converter and fuel pump? 

Offline Transman

  • We may be right or wrong, but we don't learn by being right
  • BAT Mechanic Member
  • wrench
  • *
  • Posts: 2953
  • Receptionist & Complaint Dept.
    • Ed's Auto Service, est. 1950
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #1 on: June 11, 2008, 10:01:42 PM »
Your fuel pressure is low with key on but in range idling, still a concern. GM does not like even 1 psi low and well known for  causing problems. Did you do a fuel volume test?
These are also known for crank sensor problems as well as clogged exhaust. You could remove an o2 sensor or several on the side that seems to have no exhaust and see if the engine runs smoother and if there seems to be excessive pressure trying to escape through that hole, this would indicate clogged exhaust/cats. There was only a p0300 code, nothing else? Post back, Transman
This information available in the AlldataDIY subscription
One year/one vehicle, all information including TSBs and recalls $24.95/year.
Each additional vehicle after the first vehicle and renewals are $14.95/year .
Images used with permission 2008 ALLDATA LLC. All rights reserved.
If you found this information helpful, please support BAT Auto helping you and others.
Check out Alldata, Donate to BAT Auto or Buy a BAT logo item

Offline Big Kahuna

  • Newbie
  • *
  • Posts: 7
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #2 on: June 12, 2008, 07:34:23 PM »
No on the fuel volume test.    Didn't know anything about it until now, I will check into it.    Here are the codes that came up P0300, P0420.    Exhaust pressure coming out of tail pipe was good on both sides when the codes started showing up.    I would drive it down the road a couple of miles after clearing out codes and the check engine light would flash on and off showing a pending on code P0300.    I have three incomplete monitors; misfire, fuel, and catalyst.    They will proably show the P0420 code if I keep driving it.   Ok rechecked fuel pressure today 50 with key on and 48 while running and pressure drops when I accelerate.   Removed both O2 sensors from the exhaust side that didn't have the pressure.   Exhaust is coming out hard on the first (pre) and weak on the second (post) so guess this means blocked cat.    Thanks Transman
« Last Edit: June 12, 2008, 08:38:38 PM by Big Kahuna »

Offline Transman

  • We may be right or wrong, but we don't learn by being right
  • BAT Mechanic Member
  • wrench
  • *
  • Posts: 2953
  • Receptionist & Complaint Dept.
    • Ed's Auto Service, est. 1950
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #3 on: June 12, 2008, 10:56:16 PM »
You have fuel delivery problems also, Pressure should increase on acceleration. Did the vehicle perform better when the o2 sensors were removed? Transman
This information available in the AlldataDIY subscription
One year/one vehicle, all information including TSBs and recalls $24.95/year.
Each additional vehicle after the first vehicle and renewals are $14.95/year .
Images used with permission 2008 ALLDATA LLC. All rights reserved.
If you found this information helpful, please support BAT Auto helping you and others.
Check out Alldata, Donate to BAT Auto or Buy a BAT logo item

Offline Big Kahuna

  • Newbie
  • *
  • Posts: 7
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #4 on: June 13, 2008, 06:04:24 PM »
Didn't actually put the truck on the road when I removed the O2 sensors.   At idle it sounded about the same.

Offline Transman

  • We may be right or wrong, but we don't learn by being right
  • BAT Mechanic Member
  • wrench
  • *
  • Posts: 2953
  • Receptionist & Complaint Dept.
    • Ed's Auto Service, est. 1950
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #5 on: June 16, 2008, 08:38:47 PM »
It would be a shame to throw cats on if you don't need them. Even if they are bad, I believe I would address the fuel delivery problem first. Transman
This information available in the AlldataDIY subscription
One year/one vehicle, all information including TSBs and recalls $24.95/year.
Each additional vehicle after the first vehicle and renewals are $14.95/year .
Images used with permission 2008 ALLDATA LLC. All rights reserved.
If you found this information helpful, please support BAT Auto helping you and others.
Check out Alldata, Donate to BAT Auto or Buy a BAT logo item

Offline Big Kahuna

  • Newbie
  • *
  • Posts: 7
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #6 on: June 26, 2008, 08:16:53 PM »
New fuel pump same problems P0300 Multiple Misfire.   New fuel pump showing same readings as old fuel pump.   Still think that cat needs to be replaced.    I'm open to suggestions.

Offline olds455

  • BAT Mechanic Member
  • Jr. Member
  • *
  • Posts: 45
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #7 on: June 26, 2008, 08:32:31 PM »
when the truck is running watch fuel pressure as you connect and disconnect vacuum line from fuel pressure regulator, should go up and down (up when unplugged)

Offline Transman

  • We may be right or wrong, but we don't learn by being right
  • BAT Mechanic Member
  • wrench
  • *
  • Posts: 2953
  • Receptionist & Complaint Dept.
    • Ed's Auto Service, est. 1950
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #8 on: June 26, 2008, 08:38:31 PM »
Take the front o2 sensors out again and drive the vehicle down the street, it will be louder but just drive it enough to see if the power has improved. If it has improved then the problem is clogged exhaust/cat/muffler. Post back, Transman
This information available in the AlldataDIY subscription
One year/one vehicle, all information including TSBs and recalls $24.95/year.
Each additional vehicle after the first vehicle and renewals are $14.95/year .
Images used with permission 2008 ALLDATA LLC. All rights reserved.
If you found this information helpful, please support BAT Auto helping you and others.
Check out Alldata, Donate to BAT Auto or Buy a BAT logo item

Offline Big Kahuna

  • Newbie
  • *
  • Posts: 7
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #9 on: June 26, 2008, 09:43:46 PM »
Hey thanks Transman.   I done that with the new fuel pump (remove vaccum line from regulator and it goes up and down),  pinched off the return line pressure goes past 80.   I should have left the O2 sensor out when I drove it but didn't guess I'll try tomorrow.   

Offline Transman

  • We may be right or wrong, but we don't learn by being right
  • BAT Mechanic Member
  • wrench
  • *
  • Posts: 2953
  • Receptionist & Complaint Dept.
    • Ed's Auto Service, est. 1950
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #10 on: June 27, 2008, 08:08:28 PM »
Excellent, That will be the most important info you can supply. It may not recover completely but you WILL see a big difference if the cat/exhaust is clogged. Post back, Transman
This information available in the AlldataDIY subscription
One year/one vehicle, all information including TSBs and recalls $24.95/year.
Each additional vehicle after the first vehicle and renewals are $14.95/year .
Images used with permission 2008 ALLDATA LLC. All rights reserved.
If you found this information helpful, please support BAT Auto helping you and others.
Check out Alldata, Donate to BAT Auto or Buy a BAT logo item

Offline Big Kahuna

  • Newbie
  • *
  • Posts: 7
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #11 on: July 09, 2008, 08:42:58 PM »
 fixed Conclusion,  Hey thanks Transman should have went with my first thought on the cat/converter.    Took out the O2 sensor and got my power back no check engine light.    Just got the cat changed out today $120.    Runs like a scalded dog, no check engine light.    Can't remember what other code poped up with the PO300 when this problem started but it was for the O2 sensor and cat.    :-[

FIXED, FIXED, FIXED
« Last Edit: July 09, 2008, 08:50:41 PM by Big Kahuna »

Offline Transman

  • We may be right or wrong, but we don't learn by being right
  • BAT Mechanic Member
  • wrench
  • *
  • Posts: 2953
  • Receptionist & Complaint Dept.
    • Ed's Auto Service, est. 1950
Re: 2001 GMC Sierra P0300 Multiple Misfire
« Reply #12 on: July 12, 2008, 06:24:37 PM »
Glad you got it but just a caution here, your first instinct was correct here but it is better to take a few minutes to prove it rather then replace parts. Yes, this time you would have been correct but the odds are against you hitting it every time, by testing components first, you will be assured to replace the correct defective part.
Another concern here is why did the cat go bad in the first place, my experience is bad o2 sensors will cook a cat. Check them thoroughly before you end up replacing another cat in a month or two.
Thanks for the update, Transman
This information available in the AlldataDIY subscription
One year/one vehicle, all information including TSBs and recalls $24.95/year.
Each additional vehicle after the first vehicle and renewals are $14.95/year .
Images used with permission 2008 ALLDATA LLC. All rights reserved.
If you found this information helpful, please support BAT Auto helping you and others.
Check out Alldata, Donate to BAT Auto or Buy a BAT logo item

 

©Copyright 2001-2013 batauto.com, BAT Auto Technical.
All Rights Reserved.
May not be reproduced without express written consent
.

Disclaimer: We cannot guarantee the accuracy of all information.
Please confirm the information with an appropriate manual
We try and make them as accurate as we can, but sometimes we all make mistakes.